How fast can you get to Concord, and do you do after-hours?

Concord is roughly 25 minutes up I-680, so most jobs land same-day or next morning. A dead machine costs a cafe sales, so we take after-hours and early calls when a restaurant or counter spot is down.

Do you stock Jura parts or order them?

We carry common brew-unit gaskets, descaler, and grinder wear parts on the van. Control boards, full brew units, and ceramic valves we source per machine since they vary by line like the X8, WE8, or GIGA.

What does a Jura repair usually cost?

The $75 diagnostic is waived when you go ahead with the repair. You get a written quote before any work, so you see parts and labor before we open the machine. We are an independent shop, not a Jura-authorized center.

JURA · CONCORD

Service · All Jura Models

Jura Commercial Coffee Machine Repair · Concord, CA

Jura bean-to-cup repair for Concord offices, restaurants, and small cafes.

$75 diagnostic (waived with repair)
Same-day best effort
CSLB #1136642

Call (925) 999-4095

Jura in Concord

Jura commercial service.

We service Jura super-automatic machines across Concord, from the Todos Santos Plaza restaurants downtown to the office parks and counter-service spots along Willow Pass Road and Clayton Road. Most calls in 94518, 94519, and 94520 are offices running a WE8 in a break room or a small cafe leaning on an X8 through the lunch rush.

Concord is about 25 minutes from our San Ramon shop up I-680, so a morning call usually gets a same-day or next-morning slot. Concord water carries enough scale to chew through a brew unit and clog a thermoblock, so descaling and gasket wear are the bread and butter here.

Common repairs we do

What we close on the truck.

Brew unit wear and gaskets. On a busy WE8 or X8 the brew unit seals harden and the unit starts leaking into the drip tray. We rebuild it with fresh gaskets or swap the unit and reset the count.
Descaling and thermoblock. Hard Concord tap water scales the thermoblock heater and slows the brew. We run a full descale, check flow, and talk through a water filter so it does not come back in a month.
Ceramic grinder burrs. Jura's ceramic grinder holds an edge but wears flat under cafe volume, so the dose drops and shots run weak. We regrind or replace the burrs and reset the grind.
Drainage and ceramic valves. Ceramic valves and the drain line gum up with grounds and scale, leaving water in the tray or a machine that will not finish a cycle. We clear the valve and drainage path and test it.

Models we service

Jura product lines.

GIGA X3 and X8 Professional
X8 and X10
WE8

Pricing and warranty

What it costs. What we stand behind.

$75

Diagnostic visit. Waived when you book the repair with us.
1 yr

Parts and labor warranty on completed repairs. In writing before we start.
CSLB

#1136642. Bonded and insured. We file warranty paperwork when applicable.

Nearby cities

Jura service in neighboring cities.

FAQ

Jura in Concord questions, answered.

How fast can you get to Concord, and do you do after-hours?

Concord is roughly 25 minutes up I-680, so most jobs land same-day or next morning. A dead machine costs a cafe sales, so we take after-hours and early calls when a restaurant or counter spot is down.
Do you stock Jura parts or order them?

We carry common brew-unit gaskets, descaler, and grinder wear parts on the van. Control boards, full brew units, and ceramic valves we source per machine since they vary by line like the X8, WE8, or GIGA.
What does a Jura repair usually cost?

The $75 diagnostic is waived when you go ahead with the repair. You get a written quote before any work, so you see parts and labor before we open the machine. We are an independent shop, not a Jura-authorized center.

Need Jura service in Concord?

Tell us what is broken. We will quote it.