SLAYER · LOS ALTOS
Service · All Slayer ModelsSlayer Commercial Coffee Machine Repair · Los Altos, CA
Slayer espresso machine service for downtown Los Altos coffee shops, by ADRIUM Service Solutions.
- $75 diagnostic (waived with repair)
- Same-day best effort
- CSLB #1136642
Slayer in Los Altos
Slayer commercial service.
Downtown Los Altos has a dense little coffee scene around Main Street and State Street, where the specialty cafes lean on Slayer machines for the morning and lunch crowds. In 94022 and 94024 these shops trade on shot quality, so a needle valve that drifts gets noticed fast.
San Ramon to Los Altos is about 45 to 50 minutes south. We run the machine, pin down the fault, and hand over a written quote before any work. Local water leaves scale in the boiler and valves, so descaling is part of nearly every visit here.
Common repairs we do
What we close on the truck.
- Brew needle valve and actuator. Shot consistency is the whole point downtown. When the profiling goes off, we rebuild the brew needle valve and actuator and reset the flow.
- Brew and steam solenoids. A solenoid stuck open or slow to close wrecks dosing and steam. We test and replace the brew and steam solenoids and clean the seats.
- Descaling and filtration. Los Altos water scales the boiler and brew path. We descale, then check or set up the inline filter so the valves stay clean.
- Group seals and gaskets. Daily volume plus scale ends gasket life early. We swap the group seals and portafilter gaskets to stop leaks at the head.
Models we service
Slayer product lines.
- Slayer Espresso (1, 2, 3 group)
- Single Group
- Steam EP/LP/X
Pricing and warranty
What it costs. What we stand behind.
-
$75
Diagnostic visit. Waived when you book the repair with us.
-
1 yr
Parts and labor warranty on completed repairs. In writing before we start.
-
CSLB
#1136642. Bonded and insured. We file warranty paperwork when applicable.
Nearby cities
Slayer service in neighboring cities.
More cities
Slayer across our service area.
- Slayer in Alameda
- Slayer in Alamo
- Slayer in Atherton
- Slayer in Berkeley
- Slayer in Blackhawk
- Slayer in Castro Valley
- Slayer in Concord
- Slayer in Cupertino
- Slayer in Danville
- Slayer in Dublin
- Slayer in Fremont
- Slayer in Hayward
- Slayer in Hillsborough
- Slayer in Lafayette
- Slayer in Livermore
- Slayer in Los Gatos
- Slayer in Martinez
- Slayer in Milpitas
- Slayer in Moraga
- Slayer in Newark
- Slayer in Oakland
- Slayer in Orinda
- Slayer in Piedmont
- Slayer in Pleasant Hill
- Slayer in Pleasanton
- Slayer in Richmond
- Slayer in San Jose
- Slayer in San Leandro
- Slayer in San Ramon
- Slayer in Santa Clara
- Slayer in Saratoga
- Slayer in Sunnyvale
- Slayer in Union City
- Slayer in Walnut Creek
FAQ
Slayer in Los Altos questions, answered.
-
How fast can you get to Los Altos, after hours included?
Around 45 to 50 minutes from San Ramon. A down machine is lost sales for a cafe, so we take after-hours and weekend calls when you are open. -
Do you carry Slayer parts or source them?
Seals, gaskets, and solenoid kits are stocked on the van. Needle valve components, control boards, and boiler elements are sourced through Slayer. -
What is the typical cost?
Diagnostic is $75 and waived with the repair. You get a written quote before we start any work.
Need Slayer service in Los Altos?