How fast can you get to Hillsborough, and do you cover after hours?

Plan on about 50 minutes from San Ramon to 94010. A dead machine costs a cafe every sale that morning, so we take after-hours and weekend calls when a Slayer is down and the shop is open.

Do you stock Slayer parts or order them?

Common wear items like group gaskets, brew seals, and solenoid rebuild kits we carry on the van. Boutique Slayer parts such as needle valve components, boards, and elements we source through Slayer, so those run a day or two.

What does a repair typically cost?

Diagnostic is $75 and it is waived when you book the repair. You get a written quote before we start, so there are no surprises on the invoice.

SLAYER · HILLSBOROUGH

Service · All Slayer Models

Slayer Commercial Coffee Machine Repair · Hillsborough, CA

Slayer espresso machine repair for Hillsborough cafes and private kitchens, handled by ADRIUM Service Solutions.

$75 diagnostic (waived with repair)
Same-day best effort
CSLB #1136642

Call (925) 999-4095

Slayer in Hillsborough

Slayer commercial service.

Hillsborough has almost no storefront retail, so most of the Slayer machines we see here sit in the cafes just over the line in downtown Burlingame along Burlingame Avenue, plus the private estate kitchens inside 94010. The shops that run a Slayer Espresso 2 group pull steady volume, and a stalled brew group on a Saturday means a line out the door.

From San Ramon it is roughly 50 minutes across the San Mateo Bridge to reach 94010. We come out to look at the machine, run it, and write a quote before any tool comes out. The hard water on this side of the bay is the main reason these boilers and valves fail early, so we check scale every visit.

Common repairs we do

What we close on the truck.

Brew needle valve and actuator. The needle valve is what makes a Slayer a Slayer. When flow profiling goes vague or the lever sticks, we rebuild the needle valve and actuator and reset the travel.
Group seals and gaskets. Hard 94010 water chews through group gaskets. We replace the brew group seals and portafilter gaskets so the shot stops leaking around the head.
Descaling and water filtration. Scale off the local supply clogs the boiler and slows the brew solenoid. We descale the boiler and water path and check or set up the inline filter so it does not come back fast.
Boiler element and probe. A cold steam boiler or wandering temperature is usually a failed element or level probe. We test both, swap what is dead, and verify the recovery.

Models we service

Slayer product lines.

Slayer Espresso (1, 2, 3 group)
Single Group
Steam EP/LP/X

Pricing and warranty

What it costs. What we stand behind.

$75

Diagnostic visit. Waived when you book the repair with us.
1 yr

Parts and labor warranty on completed repairs. In writing before we start.
CSLB

#1136642. Bonded and insured. We file warranty paperwork when applicable.

Nearby cities

Slayer service in neighboring cities.

FAQ

Slayer in Hillsborough questions, answered.

How fast can you get to Hillsborough, and do you cover after hours?

Plan on about 50 minutes from San Ramon to 94010. A dead machine costs a cafe every sale that morning, so we take after-hours and weekend calls when a Slayer is down and the shop is open.
Do you stock Slayer parts or order them?

Common wear items like group gaskets, brew seals, and solenoid rebuild kits we carry on the van. Boutique Slayer parts such as needle valve components, boards, and elements we source through Slayer, so those run a day or two.
What does a repair typically cost?

Diagnostic is $75 and it is waived when you book the repair. You get a written quote before we start, so there are no surprises on the invoice.

Need Slayer service in Hillsborough?

Tell us what is broken. We will quote it.