How fast can you get to a Richmond cafe?

Most days we reach Richmond in 35 to 45 minutes. A dead machine kills sales, so we run after-hours and early-morning calls when a shop can't open without espresso. Call and we'll tell you the next open slot.

Do you stock Faema parts or have to order them?

We carry common wear items on the van: E61 group gaskets, brew and steam solenoid rebuild kits, and shower screens. Boards, level probes, and specific pump assemblies we source from La Cimbali group suppliers, usually a day or two.

What does a typical Faema repair cost?

It's $75 to diagnose, waived when you approve the work. You get a written quote before we start, so no surprise totals. A gasket job runs small, a board or element replacement more.

FAEMA · RICHMOND

Service · All Faema Models

Faema Commercial Coffee Machine Repair · Richmond, CA

Independent Faema espresso machine repair for Richmond cafes and roasters, from San Ramon.

$75 diagnostic (waived with repair)
Same or next-day best effort
CSLB #1136642

Call (925) 999-4095

Faema in Richmond

Faema commercial service.

Richmond's coffee work clusters along the Marina Bay and Point Richmond waterfront, plus the cafes feeding the Ferry terminal crowd around 94801. A few roasters and specialty shops out here run older Faema heat-exchanger machines that have seen a decade of hard service. We cover 94804 and 94805 too, including the Macdonald corridor.

From San Ramon it's about a 35 to 45 minute run depending on the bridge and 24 traffic. We service Faema as an independent shop, not a factory dealer, so you get a written quote before any wrench turns. The $75 diagnostic comes off the bill once you approve the repair.

Common repairs we do

What we close on the truck.

E61 group gasket and seal leaks. Richmond's harder tap water chews through the E61-style group gaskets and seals. We pull the group, replace the gaskets, and check the shower screen so the puck seats clean again.
Brew and steam solenoid faults. A dripping group or a steam wand that won't shut off is usually a stuck brew or steam solenoid. We test the coil and valve and swap the part on Faema E61 and Teorema setups.
Heat-exchanger descaling. Scale builds fast on a plumbed line out here. We descale the heat-exchanger and boiler and check the element so recovery time and steam pressure come back to normal.
Pump and level probe. Low pressure on a Faema usually traces to the rotary pump or a scaled level probe misreading the boiler. We test both and rebuild or replace as needed.

Models we service

Faema product lines.

E71
E61 Legend and Jubile
Teorema and Emblema

Pricing and warranty

What it costs. What we stand behind.

$75

Diagnostic visit. Waived when you book the repair with us.
Written

90 days on consumables, 1 year on major parts, 2 years on sealed-system rebuilds. Quoted in writing before work starts.
CSLB

#1136642. Bonded and insured. We file warranty paperwork when applicable.

Nearby cities

Faema service in neighboring cities.

FAQ

Faema in Richmond questions, answered.

How fast can you get to a Richmond cafe?

Most days we reach Richmond in 35 to 45 minutes. A dead machine kills sales, so we run after-hours and early-morning calls when a shop can't open without espresso. Call and we'll tell you the next open slot.
Do you stock Faema parts or have to order them?

We carry common wear items on the van: E61 group gaskets, brew and steam solenoid rebuild kits, and shower screens. Boards, level probes, and specific pump assemblies we source from La Cimbali group suppliers, usually a day or two.
What does a typical Faema repair cost?

It's $75 to diagnose, waived when you approve the work. You get a written quote before we start, so no surprise totals. A gasket job runs small, a board or element replacement more.

Need Faema service in Richmond?

Tell us what is broken. We will quote it.