Our CM 5 shut itself off and will not come back on. Is it the board?

Maybe, but the board is the last thing we condemn. A failed power supply, a loose connector or a blown thermal fuse can look exactly the same from the outside. On our bench we test each of them in turn and quote only the part that actually failed.

Is a CM 5 worth fixing, or should we replace it?

That depends on the fault. Seals, a sensor or a set of burrs are modest repairs, and the machine has plenty of life after them. A failed board on a heavily worn machine is a closer call, and the written quote puts that choice in front of you before any work.

Can San Pablo's EBMUD water cause electrical faults in a Miele?

Not directly. The water here is soft to moderate. Water reaches the electronics through leaks, and a dripping seal above a board can do real damage. If your machine leaves water underneath it, stop using it and have it checked.

MIELE PROFESSIONAL · SAN PABLO

Service · All Miele Professional Models

Miele Professional Commercial Coffee Machine Repair · San Pablo, CA

Miele Professional display, sensor and control board diagnosis for San Pablo homes and small offices.

$175 pickup deposit. Pickup, bench diagnosis, and return are included. The deposit is not credited toward the repair. Repair work is quoted separately.
Bench diagnosis: up to one week. Most repairs: 3–4 weeks.
Same-day pickup may be available. Same-day repair is not offered.
CSLB #1136642

Call (925) 999-4095

Miele Professional in San Pablo

Miele Professional commercial service.

San Pablo sits on the flat land between the Berkeley Hills and the bay, with postwar single-family houses, row houses and a large share of apartments. A countertop Miele fits any of those kitchens. When one goes dark, freezes on a message or shows an error it will not clear, the electronics get the blame, yet a sensor or a loose connection is often the real fault rather than the board.

A control board is one of the costlier parts in the machine, so we test everything around it first. We pick the machine up, trace the fault on our bench and send a written quote, and nothing gets replaced until you approve it. ADRIUM works on Miele as an independent shop, not a Miele service center, under CSLB #1136642.

$175 pickup deposit. Pickup, bench diagnosis, and return are included. The deposit is not credited toward the repair. Repair work is quoted separately. Bench diagnosis can take up to one week; most repairs take 3–4 weeks. Same-day pickup may be available, but same-day repair is not offered. 6 months on parts and labor; 90 days on consumables.

Common repairs we do

What we repair on the bench.

Display that stays dark or freezes. A blank or frozen screen can come from the display, its cable or the board behind it. We test the power supply and the connections first, then the display itself, so you pay for one part instead of three.
Temperature sensor reading wrong. A sensor that reports the wrong temperature makes the machine underheat, overheat or stop with an error. We measure the sensor against a known value on the bench and replace it if it has drifted out of range.
Control board fault after everything else tests good. When the sensors, wiring and display all check out and the machine still misbehaves, the board is the likely cause. We confirm that before ordering one, then install the replacement and run the machine through every drink it makes.

Models we service

Miele Professional product lines.

CM 5, 6, 7 series
CVA built-in
professional units

Pricing and warranty

What it costs. What we stand behind.

$175

Pickup deposit. Pickup, bench diagnosis, and return included. Repair quoted separately.
3–4 weeks

Most repairs. Bench diagnosis can take up to one week.
6 / 90

6 months on repair parts. 90 days on consumables.

Recent work

Miele Professional jobs we have closed.

Alamo, CA · Miele built-in coffee system

Miele Built-In Coffee System Deep Clean in Alamo (CVA6805)

Weak, short pours and faults from a brew unit and grinder caked with old grounds and coffee oil.
Read case →

See all case studies →

Nearby cities

Miele Professional service in neighboring cities.

More cities

Miele Professional across our service area.

FAQ

Miele Professional in San Pablo questions, answered.

Our CM 5 shut itself off and will not come back on. Is it the board?

Maybe, but the board is the last thing we condemn. A failed power supply, a loose connector or a blown thermal fuse can look exactly the same from the outside. On our bench we test each of them in turn and quote only the part that actually failed.
Is a CM 5 worth fixing, or should we replace it?

That depends on the fault. Seals, a sensor or a set of burrs are modest repairs, and the machine has plenty of life after them. A failed board on a heavily worn machine is a closer call, and the written quote puts that choice in front of you before any work.
Can San Pablo's EBMUD water cause electrical faults in a Miele?

Not directly. The water here is soft to moderate. Water reaches the electronics through leaks, and a dripping seal above a board can do real damage. If your machine leaves water underneath it, stop using it and have it checked.
What does the Miele Professional pickup deposit cover?

$175 pickup deposit. Pickup, bench diagnosis, and return are included. The deposit is not credited toward the repair. Repair work is quoted separately.
How long does Miele Professional bench repair take?

Bench diagnosis can take up to one week; most repairs take 3–4 weeks. Same-day pickup may be available, but same-day repair is not offered.
What warranty applies to Miele Professional coffee-machine repair?

6 months on parts and labor; 90 days on consumables.

Need Miele Professional service in San Pablo?

Tell us what the machine is doing. We will confirm pickup.