Our building needs a loading slot booked for any repair. How does that work?

Tell us the building's rules when you book. We schedule the visit inside the window the manager gives, bring what fits through the freight path and keep the work at the machine. Parts that need ordering go on a second visit booked the same way.

Our Ultra-NX shows an error code and restarts on its own. Is the board gone?

Not necessarily. Restarts can come from a loose connector, a sensor sending bad readings or a supply problem at the outlet. We test those first. If the board fails the tests, the written quote names it and you decide.

Is the machine safe to run while it drips from the front?

Run it only as long as you must. A front leak means a seal or gasket has failed, and product that reaches the drive or the base can ruin a bearing or corrode parts. Wipe it down, keep an eye on the drip tray and book the seal repair soon.

BUNN · EMERYVILLE

Service · All Bunn Models

Bunn Frozen Beverage Machine Repair · Emeryville, CA

Bunn frozen drink machine repair in Emeryville, planned around building access and your opening hours.

Bunn equipment connected to the building plumbing is diagnosed on site for $99, credited toward the repair. Countertop units come to our bench; we confirm the bench price when you book.
Same or next-day best effort
CSLB #1136642

Call (925) 999-4095

Bunn in Emeryville

Bunn commercial service.

Emeryville fits shops, offices and condos into a small city between Berkeley and Oakland, and the Powell Street and Bay Street district is its commercial heart. In a mixed-use building, a service visit may need a loading slot, an elevator booking or a vendor form on file with the manager. Tell us what your building requires and we set the visit up around it.

Emeryville visits are handled by our technician, who is based in Benicia. At the machine we check the Ultra-2 or Ultra-NX under load: barrel temperature, the drive, the seals and the control side. The diagnostic covers finding the fault, and nothing is replaced until you have the written quote. For Bunn connected to the building plumbing, the on-site diagnostic is $99, credited toward repair. We confirm countertop bench pricing when you book.

Common repairs we handle.

Overfreezing that locks the auger solid. When a control fails to end the freeze, product sets solid and the auger cannot turn. Forcing the machine on can strip the drive. We test the control and the sensor that should have ended the cycle, replace what failed and inspect the drive for damage from the lockup.
Sensor fault shutting the machine down mid-shift. A sensor that reads wrong can stop a barrel in the middle of service, even when the refrigeration is fine. We read each sensor against the actual barrel temperature and product level, then replace the one that has drifted and clear the fault history.
Worn auger bearing on a machine that runs all day. Long daily run hours wear the bearings behind the auger. The first sign is a low hum that changes pitch, then a knock. We replace the bearing and check the gear motor before the wear spreads into the gearset.

Models we service

Bunn product lines.

Ultra-2 and Ultra-NX frozen and granita dispensers
JDF juice and drink units

Pricing and warranty

What it costs. What we stand behind.

Price at booking

Bunn equipment connected to the building plumbing is diagnosed on site for $99, credited toward the repair. Countertop units come to our bench; we confirm the bench price when you book.
Written

Parts and labor, 3 months to 2 years depending on the type of repair. Quoted in writing before work starts.
CSLB

#1136642. Bonded and insured. We file warranty paperwork when applicable.

Recent work

Bunn jobs we have closed.

Union City, CA · Commercial Bean-to-Cup Coffee Machine

Bunn Crescendo Commercial Coffee Machine Repair

A busy Union City location was losing its coffee service. The Crescendo's brew path had worn out: stiff, stained silicone lines and spent valve diaphragms and seals.
Read case →

See all case studies →

Nearby cities

Bunn service in neighboring cities.

More cities

Bunn across our service area.

FAQ

Bunn in Emeryville questions, answered.

Our building needs a loading slot booked for any repair. How does that work?

Tell us the building's rules when you book. We schedule the visit inside the window the manager gives, bring what fits through the freight path and keep the work at the machine. Parts that need ordering go on a second visit booked the same way.
Our Ultra-NX shows an error code and restarts on its own. Is the board gone?

Not necessarily. Restarts can come from a loose connector, a sensor sending bad readings or a supply problem at the outlet. We test those first. If the board fails the tests, the written quote names it and you decide.
Is the machine safe to run while it drips from the front?

Run it only as long as you must. A front leak means a seal or gasket has failed, and product that reaches the drive or the base can ruin a bearing or corrode parts. Wipe it down, keep an eye on the drip tray and book the seal repair soon.

Need Bunn service in Emeryville?

Tell us what is broken. We will quote it.