How soon can you reach Alamo?

We are based in San Ramon, 10 to 15 minutes out. Same or next-day is realistic when there is a window open. I text the appointment confirmation with the truck arrival window so you are not sitting around waiting.

Do I really need to clean a heat-pump dryer condenser every year?

Yes. That is the single most common reason a ventless dryer here stops drying well. The fins pack with lint and the heat exchange drops off. Annual cleaning keeps cycle times where they should be. I do it as a maintenance visit if that is all you need.

LAUNDRY REPAIR · ALAMO

Laundry Repair · Alamo, CA

Washer and dryer repair in Alamo, 94507. Estate laundry rooms, heat-pump dryers, large-capacity front-loaders.

$75 diagnostic (waived with repair)
Same or next-day best effort
CSLB #1136642

Call (925) 999-4095

Laundry Repair in Alamo

Laundry Repair in Alamo.

Alamo kitchens lean Sub-Zero and Wolf, but the laundry rooms behind the Round Hill and Stone Valley estates are their own thing. Big LG and Samsung front-loaders on pedestals, Electrolux Perfect Steam pairs, and Bosch condensing or heat-pump dryers in the remodels that went for a closet-free ventless setup. These are 90s and 2000s-era homes, so a lot of the original pairs are now in the bearing-wear and control-board window. The heat-pump dryers in particular get a call I see often: drying times creeping up because nobody cleaned the condenser.

Older Westside Alamo near Las Trampas Creek runs simpler. KitchenAid and GE Profile pairs from the 80s and 90s remodels, vented dryers, top-load washers. Those are mostly single-visit fixes. Drain pump, lid switch, a dryer element. I diagnose with a meter before I open a major panel.

Common repairs we do

What we close on the truck.

Bosch or Electrolux heat-pump dryer, takes forever to dry. Condenser fins clogged. Needs cleaning about once a year. I clean the condenser, check cycle time against spec, and leave a sticker with the next due date. Most of the slow-drying ventless calls I get are this, not a failed machine.
Electrolux Perfect Steam, torn door boot. OEM boot on the truck, 45-minute replacement done right. The tear leaks onto the laundry-room floor fast, so I do not put it off.
GE or KitchenAid vented dryer, drum bearing growl. Rear bearing wears out at the 8 to 10 year mark on the Westside units. I replace the rear bearing, front felt seal, idler pulley, and belt together so it does not come back as a callback.
LG front-load, LE motor fault. Rotor-position sensor drifted out of spec. Single-visit sensor swap, under five minutes once the back is off. This is not a motor failure, so it should not be priced like one.

Pricing and warranty

What it costs. What we stand behind.

$75

Diagnostic visit. Waived when you book the repair with us.
1 yr

Parts and labor warranty on completed repairs. In writing before we start.
CSLB

#1136642. Bonded and insured. We file warranty paperwork when applicable.

Nearby cities

Laundry Repair in neighboring cities.

More cities

Laundry Repair across our service area.

FAQ

Laundry Repair in Alamo questions, answered.

How soon can you reach Alamo?

We are based in San Ramon, 10 to 15 minutes out. Same or next-day is realistic when there is a window open. I text the appointment confirmation with the truck arrival window so you are not sitting around waiting.
Do I really need to clean a heat-pump dryer condenser every year?

Yes. That is the single most common reason a ventless dryer here stops drying well. The fins pack with lint and the heat exchange drops off. Annual cleaning keeps cycle times where they should be. I do it as a maintenance visit if that is all you need.

Need laundry repair in Alamo?

Tell us what is broken. We will quote it.