How fast can you reach Menlo Park from San Ramon?

I route Menlo Park with Atherton and Palo Alto on the Mid-Peninsula day, two to three days a week. Drive time is 45 to 60 minutes. Booked windows get a written arrival time before I leave the shop.

My Thermador range clicks but the burner will not light. Is that the control board?

Rarely the board. Almost always the spark module, the ignitor electrode, or carbon buildup at the tip. I clean, re-gap, and bench-test the gas valve micro-switch first. The fix is usually a single visit.

Can you work on a panel-ready range built into custom cabinetry?

Yes. A lot of the Sand Hill and Allied Arts installs are boxed into custom panels. I bring floor protection and take the time to pull and reset without scratching anything.

COOKING APPLIANCE REPAIR · MENLO PARK

Cooking Appliance Repair · Menlo Park, CA

Pro range, wall oven, and cooktop repair across Menlo Park 94025 and the 94027 overlap.

$75 diagnostic (waived with repair)
Same-day best effort
CSLB #1136642

Call (925) 999-4095

Cooking Appliance Repair in Menlo Park

Cooking Appliance Repair in Menlo Park.

Cooking calls in Menlo Park split by neighborhood. Sand Hill and Allied Arts run the estate setups: Wolf and Thermador pro ranges with Sub-Zero columns and Miele wall ovens. A lot of those kitchens were remodeled in the last fifteen to twenty years, so the Thermador Star Burner ranges are now into the spark-module and ignitor-electrode age, and the Wolf dual-fuel broilers need attention at the broiler ignitor. Downtown and Felton Gables run the KitchenAid commercial-style ranges and Bosch Benchmark wall ovens, where the European hidden bake element is the steady call.

I meter before I condemn a part. A clicking Star Burner with no light is almost always spark module, electrode, or carbon buildup, not a board, and I bench-test the gas valve micro-switch before condemning anything. On a Bosch wall oven with a dead bake element I want the model number ahead of the visit so I bring the right element and close it in one trip. Gas work here is licensed under CSLB and I carry the leak detector for the panel-ready installs where the range is boxed into custom cabinetry.

What the work looks like

A gas oven burner lighting clean after service.

A gas oven bake burner lighting with an even blue flame after service. The white bar is the glow-bar igniter, and when it weakens the oven will not heat even though it still glows.

Common repairs we do

What we close on the truck.

Thermador Star Burner clicking, no light. Clean and re-gap the ignitor electrode, bench-test the gas valve micro-switch, replace the spark module only if it tests dead. Usually one visit.
Wolf dual-fuel range, broiler will not light. Infrared broiler ignitor and upper thermocouple fail together. I carry the common ignitors and thermocouples and test the micro-switch before closing up.
Bosch Benchmark wall oven, dead bake element. Hidden European bake element. Pull the rear panel, swap, verify resistance, run a full bake cycle. Two-hour single visit with the model number ahead of time.
Miele wall oven, no heat or temp drift. Usually the oven temp sensor out of spec, not the board. Sensor swap is quick. I confirm the reading at temperature before signing out.

Pricing and warranty

What it costs. What we stand behind.

$75

Diagnostic visit. Waived when you book the repair with us.
1 yr

Parts and labor warranty on completed repairs. In writing before we start.
CSLB

#1136642. Bonded and insured. We file warranty paperwork when applicable.

Nearby cities

Cooking Appliance Repair in neighboring cities.

More cities

Cooking Appliance Repair across our service area.

FAQ

Cooking Appliance Repair in Menlo Park questions, answered.

How fast can you reach Menlo Park from San Ramon?

I route Menlo Park with Atherton and Palo Alto on the Mid-Peninsula day, two to three days a week. Drive time is 45 to 60 minutes. Booked windows get a written arrival time before I leave the shop.
My Thermador range clicks but the burner will not light. Is that the control board?

Rarely the board. Almost always the spark module, the ignitor electrode, or carbon buildup at the tip. I clean, re-gap, and bench-test the gas valve micro-switch first. The fix is usually a single visit.
Can you work on a panel-ready range built into custom cabinetry?

Yes. A lot of the Sand Hill and Allied Arts installs are boxed into custom panels. I bring floor protection and take the time to pull and reset without scratching anything.

Need cooking appliance repair in Menlo Park?

Tell us what is broken. We will quote it.